Frequently Asked Questions
The prices vary depending on size and start from as low as $1999. Please click here for models and prices
Our boxes are imported from our Australian parent company (The Pool Pump Cover). Delivery lead times will depend on destination. Please click here for lead times
The box comes flat packed in large cardboard boxes and is hand unloaded by our driver at drop ship destination.
The enclosures come flat packed in large cardboard boxes. Between each steel panel is a layer of 1/12 inch thick packing foam, with a maximum of 4 panels per box (max weight 121 pounds). The edges and faces of the box are surrounded in ¼ inch thick polystyrene foam.
The process of galvanising steel is the placement of a thin coat of zinc over steel to protect it from rust. The Pool Pump Cover uses 3/8 inch steel hot-dipped in zinc creating a coated commercial forming steel with a spangled surface, which is then skinpassed to improve surface quality.
The Pool Pump Cover uses only galvanised steel with a minimum 1/80 inch zinc coating, meeting and exceeding Australian and International standards for galvanised steel:
- AS/NZS 1365:1996 (R2016) AS 1397-2011 ISO 9001:2015 Quality System certified
The unique design of our Pool Filter / Pump enclosures means that there are absolutely NO NUTS & BOLTS and NO need for any TOOLS to assemble the box. On average, models that are < 67 inches in width (single) take 15-20 minutes to assemble and models that are > 67 inches (double) take 2 persons 45 – 60 minutes to assemble.
The panels of the enclosure are joined together at the bottom by 4 corner brackets and locked at the top by 4 corner caps (additional 4 corner caps and 2 straight brackets for enclosures > 67 inches)
The box comes flat packed in large cardboard boxes and is hand unloaded by our driver at drop ship destination
Please click here to watch our 3D assembly instructions
The panels (of the enclosures) are lined with 20mm Australian made Acoustic Foam – industrially affixed to the interior of the panels. The Dark Grey foam is typically a grade of 29/400 which equates to the following:
- Density of 28 to 31 kg/m3
- Tear resistance of 400N/m (minimum)
These properties, combined with the design of the enclosure, facilitate an 80-81% reduction in noise when applied to the enclosure – see independent Acoustic Report here.
The Foam is treated with Ultra Fresh protection to guard against dust mites, bacteria and fungi.
All our products are imported directly from Sydney, Australia, made of 100% Australian products, including BlueScope© Galvabond steel and Dunlop Acoustic Foam. Air freight is used (unless specifically requested as sea freight) for all orders, and fulfilment typically take between 14 and 28 days from date of payment.
All enclosures are available in backless, side-less and side access variations.
A ‘backless’ enclosure is more appropriate when there is less than 2 inches from the wall and the equipment (e.g.: a pipe, a filter, pump etc.). The design of the backless enclosure will allow you to lift the lid without hitting the wall / fence. They have additional ‘brackets’ at the back which get affixed (screwed / bolted) to the wall / fence.
Please note, backless enclosures therefore add 2 inches to the depth – Please click here for pictures of backless enclosures
A side-less enclosure is useful/required when you do not have 1 inch of space down one side of the enclosure to fit the side panel. An example of that is when there are pipes or other equipment too close to a side wall which prevents you from sliding the side panel (of the enclosure). The design uses the same ‘wall brackets ‘which are used for ‘backless’ enclosures. A side-less enclosure adds 2 inches to the width and comes with a door stay in lieu of a gas strut
Side access is an enclosure that also has a removable door on one of the sides (in lieu of the normal side panel). This is particularly useful when there is confined access to the enclosure (e.g.: it is located at the side of the house on a narrow thoroughfare). Having a side access panel allows you access the enclosure from the side (rather than the front). Please click here for pictures.
Please also note, gas struts are not available on the side where side-access or sideless is requested.
Feet are available to level the enclosure in the case of uneven ground, to a maximum of 1½ inches. These are optional and when purchased, there will be 2 feet provided for every corner
Footings are chemically treated timber pine sleepers – cut to the size if the enclosure and come pre-drilled with all the relevant screws to assemble. They are used / needed when there is no even or level ground (the enclosure needs to sit on an even or level surface such as a concrete slab or pavers)
Please note the footings will increase the height of the enclosure by 3.5 inches.
Yes. The Galvabond steel panels may be ‘core drilled’ to accommodate pipework, electrical cabling etc. Please note, The Pool Pump Cover suggests that a (silicone) sealant is used to cover the core drill cut to reduce the likelihood of rust impacting the panel.
All enclosures have a 1-inch gap along the full width at the back and front (between the bottom of the lid and the top of the rear / front panel). The gaps allow for adequate ventilation as well as for running power cords in / out of the enclosure (power points can. remain hanging on an external wall /fence)
The Pool Pump Cover provides a dressed pine backing board on each standard enclosure to mount such devices as the controller, GPOs, light switches and other electricals. This board is 7½ inches high and ¾ inch deep and runs along the full width of the enclosure.
The dressed pine board can be fitted to a side panel as an optional extra.
The Pool Pump Cover offers the following colors as standard:
- Night Sky Black; Satin finish (R 42 G 43 B 43 LRV 4%)
- Classic Cream; Satin finish (R 227 G 210 B 176 LRV 69%)
- Pale Eucalypt; Satin finish (R 120 G 129 B 106 LRV 25%)
- Stone Grey; Satin finish (R 144 G 142 B 138 LRV 32%)
- Terrain; Satin finish (R 100 G 65 B 51 LRV 10%)
- Cottage Green; Satin finish (R 54 G 80 B 69 LRV 10%)
- Woodland Grey; Satin finish (R 82 G 82 B 77 LRV 12%)
- Surfmist; Satin finish (R 213 G 213 B 205 LRV 69%)
- Ironstone; Satin finish (R 74 G 78 B 85 LRV 11%)
- Monument; Satin finish (R 66 G 66 B 67 LRV 9%)
Please click here for a color chart.
Yes. We can also custom fabricate any size. Prices will vary depending on how many panels needed to be custom fabricated. So, for example; if you can utilise a standard height and width, then we would only need to customise the depth, fabricating only the side and lid panels; thus reducing the additional cost of customization.